China agricultural horizontal grinders mixers
from 1 to 5 MT per hour

HGM series of Feed processing machine is a new type of horizontal grinder mixer, which is widely used in feed, food, pharmaceutical, chemical, paint and other industries for making powder materials in size 40mesh and up. The mixer grinder parts are a hammer crushing system, a mixer and two of the auto. feeder systems.

With an advanced double helical ribbon blender structure, we could easily achieve high uniformity of mixed material by adjusting the gap between the mixer tank wall and the central ribbon blender and to reduce the residual effect. In the past, during the mixing process we usually have a problem that, the high density materials or the high specific gravity materials are always sunk to the bottom of the mixer tank to enable an invalid mixing, now we can say, the problem was fully solved.


Complete machine diagram

Technical Data

 

HGM-500

HGM-1000

Working capacity

1~3MT/h, 500kgs/batch

2~5MT/h, 1000kgs/batch

Working capacity for Pig feed

2MT/h

3MT/h

Working capacity for Poultry feed

3MT/h

5MT/h

Power supply

380V

380V

Spindle speed

2930RPM/min.

2930RPM/min.

Hammer Grinder power

15KW

15KW

Mixer power

11KW

15KW

Auto. Feeder power

2*3KW

2*3KW

Mixer Tank size

2*1.2*1.8M/500kg

3*1.2*2.5M/1000kg

Time for mixing

4-10min/batch

4-10min/batch

Mixing coefficient of variation

≤8%

≤8%

Mixer filling rate

80%

80%

Machine weight

1850kg

2350kg

Machine running size (with Feeder)

3.5*2.3*2.5M

3.8*2.5*2.7M

Machine shipping size (Feeder dissembled)

3.5*1.2*2.5M

3.7*1.3*2.7M

 Other horizontal grinder mixer components information

A. Raw materials grinding entrance

B. Materials no need grinding entrance

C. Materials Exit connecting to H.

D. Materials Exit connecting to F.

E. Auto. Feeder motor

F. Entrance of Grinder

G. Grinder motor

H. Entrance of Mixer for other materials no need grinding.

I. Air hole

J. Grinder

   

K. Exit of the mixed materials (finished product exit).

Mixer grinder machine shematic diagram
   

Raw materials hopper embedded in floor

Double helical ribbon blender system

   

Single helical ribbon auger inside Auto. feeder

Mixer motor 15kw

Sieves

All the sieves are made in steel sheet in 2mm thickness.
Size: 1530*125*2mm
3mm mesh hole sieve is the standard.
Sieve could be available in mesh hole 1.8, 2.5, 3, 4, 6, 8, 10, 12 & 14mm to buyer's 0ption or depends on the feed type they need.
Usually for poultry feed we suggest 1.8/2.5/3mm sieve, for Chicken feed we suggest 8/10/12/14mm sieve while for cow it needs 4/6mm sieve.
Using life: one year

Grinder hammer pieces set

Installation

1. The workshop flooring foundation should be solid, flat and plain and strong enough.

2.  Make sure that all the fasteners are well stated in safe and strong position, all the moving parts are rotating flexible and in smooth operation.

3.  All the motors and reducer are regularly greased following to the using guidance.

4. After installation, please make sure that all components are set up properly, especially the Motor direction, a wrong Motor direction will cause big problem.

Usage

1. Each time before exact start of grinding and mixing, please make the machine in empty running to make sure that every part of the machine are in good conditions.

2. Metal piece, stone piece or any other hard materials are not allowed to mix in the grinding materials or Mixing materials, otherwise the machine components will be destroyed.

3. Please always start the mixer when the tank body is 80% full or at least the materials level is higher than the mixer spindle.

4. By adjusting the bearing chambers on both side tank body, the gap from the mixer tank wall to the outside of ribbon blender could be changed between 0~5mm, this is to meet the different requirement  of processing materials. After adjustment, please don’t forget to make the machine in empty running before an exact use.

5. Any hand touching or wooden/metal stick moving inside the Materials entrances or Tank body is forbidden. 

Maintenance

1. Machine bearings are requested to be cleaned and greased after using 60 days. We suggest you to choose Kea grease ZG-3.

2. Gearbox requests a grease replacement after using 15 days, then you need to replace again every 60 to 90 days after continue working.

3. Hammer pieces: usually the hammer pieces can be used for one year but you need to change in 6 months the direction of hammer pieces. In the first 6 months you install the hammer pieces in one side hole, then the othe 6 months you could change to install by another hole, till the hammer pieces will be fully damaged.

4. Sieves: the use life of sieve could be one year, depends on the way of using. Just change when you see the granulars are not in requested sizes.

Other export information

Product HS Code 84361000 for Import/Export Custom Formalities Use

Disasembled naked machines loading inside container.

We suggest to order with the machines several hammers sets and sieves

Possible to mix the 2 models in one container

One twenty feet container can load 2 machines.
Possible to load several cubic meters of small items besides the machines

Minimum order: 1 machine but the sea freight % will be higher

Feel free to consult us if you need higher capacity machines but in any case send please a very precise request.

Vertical mixers-grinders

Heavy duty generators to run the mixers grinders

[E3CIT home]  [Agri machinery index] [Contact]

E3CIT company: a SCAC Network member